A Step-by-Step Guide to Setting Up a Tub
A Step-by-Step Guide to Setting Up a Tub
Blog Article
Every person may have their private piece of advice when it comes to Tools You Need to Install a New Bathtub .
Mounting a tub isn't specifically rocket science, however it does require strong plumbing, woodworking, and in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably tough project. If the old tub is easily obtainable, the project can relocate quickly; if you need to open a wall surface to remove the old bathtub and also position the brand-new bathtub, the job is much harder. In either case, the task is within a house handyman's abilities, although you will require an assistant to move out the old bathtub and set in the brand-new one. Make sure you have qualified on your own for the job as well as fit trying it. Instead of employing a contractor to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Possibilities are you might require a specialist plumber to make tube connections.
This short article will certainly aid you install a new bath tub in your bathroom if you have already purchased a new tub as well as do not require to transform the setup of your previous water supply pipelines.
Your devices and also material checklist should comprise the following:
Planning for the Setup
Firstly, the sustaining framework supplied with the bath needs to be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to now be ready to be fitted in its last placement.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the supply of water. After doing so, turn on the faucets to drain pipes any water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic due to the restricted accessibility that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a fabric prepared for the staying water that will come from the pipes. When the supply pipes have been eliminated, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to proceeding to fit the new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Using the two wooden boards under its feet, place the tub in the needed placement. The wood boards are handy in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the bathtub up until the level reviews degree.
To install taps, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipe by making a compression join; then do the exact same for the other faucet.
Activate the water and also check all joints and brand-new pipework for leakages and also tighten them if essential. Fill the bathtub and also check the overflow electrical outlet and also the regular electrical outlet for leaks.
Finally, fix the bath paneling as defined in the supplier's instruction manual. Tiling and sealing around the bath tub needs to wait up until the tub has been used at the very least when as this will settle it right into its last setting.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in area in between the tap and the sink. Safeguard the faucet in place with the manufacturer given backnut. As soon as the tap is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The previous kind must be linked to the tap ends initially, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to split a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, resulting in difficulties with moisture and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to enable the activity experienced when the tub remains in usage. The sealant can split fairly very early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the market. It is suggested to fit the tiles utilizing waterproof or waterproof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am just very focused on A Step-by-Step Guide to Installing a Bathtub and I am hoping you appreciated the entire post. You should take the time to share this post if you enjoyed reading it. I am grateful for your time. Visit again soon.
Get A Free Quote
Report this page